top of page
1.png

FormFutura® MetalFil - Classic Copper

About The Materials 

MetalFil - Classic Copper is a PLA type of 3D printer filament with 80% copper filling. It 3D prints heavyweight copper parts which are nearly indistinguishable from genuine copper casted objects.

Materials Documentations

Formfutura MetalFil Classic Copper is a composite PLA (polylactic acid) filament that is gravimetrically filled with approximately 80% copper powder. The high copper content in MetalFil Classic Copper makes 3D printed objects nearly indistinguishable from genuine copper casted objects. MetalFil Classic Copper can be post-processed with various patina effects.Unique featuresVery high copper-filling of 80%Real copper look, heavyweight, and “cold” copper metal feelApproximately 300% heavier than PLA (density of 3.4 g/cc)Compatible with full metal, PEEK, and PFTE hotendsCompatible with direct drive and Bowden style extrudersCompatible with ≥ 0.4mm hardened nozzles with retraction settings enabledEasy to post-processMetalFil can be brushed, sanded, polished, waxed, coated and patina post-processed


Applications

  • Aesthetics, design, and art

  • Figurines and miniatures


General printing guidelines *

Nozzle size: ≥ 0.4mm

Layer height: ≥ 0.2mm

Experience level: Beginner

Print temp: ± 200 - 230° C *

Fan speed: 50-100%

Heat bed: ± 0 - 60° C

Enclosure needed: No


*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.


Post processing MetalFil - Classic Copper


Brushing and/or sand grinding

Once printed MetalFil - Classic Copper objects can very easily be brushed with a brass brush or sanded with fine-grit sandpaper. By brushing and/or sand grinding your printed object you will brush/shine up the high concentration of copper powders.


Build-in white polish feature

After being brushed and/or sanded MetalFil - Classic Copper will reveal its white polish feature. A very thin white layer/haze on your object will now allow you to easily polish your 3D print into a beautiful copper object.


Professional polishing with a rotary tumbler

Post-processing a MetalFil - Classic Copper 3D printed object with a rotary tumbler will make your FDM 3D printed object indistinguishable from genuine copper casted objects.


Patina post-processing

You can create several patina effects on MetalFil - Classic Copper printed objects in just one day time. With an ammonia and soda treatment you can for instance easily create a beautiful ancient green/blue weathering effect on your copper object.


Waxing and coating

After every above-mentioned post-processing measure, you can always wax or coat your printed object to get an incredible shine effect. Waxing can be done with products such as beeswax and for coating one can think about products such as XTC-3D.


Nozzle cleaning

When printing with filled/composite filaments it is recommended to clean your nozzle immediately after printing by feeding 15-20cm PLA filament through your nozzle. This will make sure that any potential fillers are flown out of your nozzle. It is even better to use glow in the dark PLA as the extremely hard phosphorous particles are much more likely to scrape out residual waste from your nozzle.


Compliance *

This filament is compliant to below listed directives and regulations.

  • RoHS directive 2011/65/EC

  • REACH directive 1907/2006/EC

*) This declaration of conformity to directives and regulations is prepared according to our present standard of knowledge and may be amended if new cognitions are available and applies only for the above described products.

Applications

Materials Informations

Weight:

Diameter:

Colour:

250g, 750g, 1500g

1.75mm, 2.85mm

Natural